Reset your Holosun EPS Carry Red Dot Sight

Occasionally, you may want to reinitialize your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the settings or are experiencing unexpected issues. Fortunately, resetting your Holosun is a easy process that can be achieved in just a few procedures.

Begin by ensuring your red dot sight is powered on.
Find the small reinitialize button on the rear of the sight.
Employ a thin tool to activate the reset switch for approximately 7 seconds.
Release the reset button and your Holosun EPS Carry Red Dot sight will power cycle.
The red dot sight should now be returned to its factory settings.

Restore Your Holosun EPS Carry Red Dot to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it to its factory configuration is a breeze. First, find the tiny button on the side of your optic. Then, keep pressed it for around ten seconds until you see a brief flash. Your Holosun EPS Carry is now reset to its factory settings, ready for precise aiming.

revive your Holosun EPS Carry Back to Action

Is your beloved Holosun EPS Carry experiencing some glitches? Don't despair! A simple factory reset can often solve the problem and get your red dot sight back to its former glory. Before you begin, remember to detach the battery from your Holosun EPS Carry to prevent accidental activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these simple steps:

Press and hold the power button for approximately 7 seconds.
A message will flash, indicating that the reset is being performed.
Release the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can insert the battery and test your sight's functionality. If you encounter here any further difficulties, don't hesitate to contactHolosun's customer support.

Revert Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Adhere to these steps carefully to ensure a successful factory reset.

Initially, Turn on your Holosun EPS Carry by pressing the power button.
Subsequently, press and hold both the mode button and the up/down adjustment button simultaneously.
During continue holding these buttons, tap the power button once.
You will show a confirmation prompt indicating that the reset process is initiated.
Enable the process to complete. This may take a few moments. Once done, your Holosun EPS Carry will automatically deactivate.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Reset All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Pressing a specific button combination. Consult your Manual for the exact button sequence for your model. Once in the settings menu, look for an option that says "Factory Default". Select this option and confirm the reset. Your sight will then power off and restart with all settings Restored to their default values.

Reset your Holosun EPS Carry via a Factory Original Settings

If your Holosun EPS Carry is acting up, a factory reset might be the solution. This will restore your sight to its initial settings, clearing any custom configurations you've made. To execute this reset, adhere to these easy steps:

Initially, find the reset lever on your EPS Carry.
Next, press a small object, like a paperclip, to depress the reset button.
While keep the reset button pressed, power on your EPS Carry.
The sight will display a message showing that the reset is successful.

When the reset is finished, your EPS Carry will be returned to its factory settings.